 |
924Board.org Discussion Forum of 924.org
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
924 FAQ (Technical)| Search found 61 matches |
| Author | Message |
|---|---|
 Topic: No voltage to air flow meter. |
|
| 16again2009 Replies: 2 Views: 5606 |
 Forum: General Discussions Posted: Tue Jul 26, 2022 6:12 am Subject: No voltage to air flow meter. |
| Never mind. I just discovered my meter wasn't working on volts. Thanks for your response. | |
| Topic: No voltage to air flow meter. |
|
| 16again2009 Replies: 2 Views: 5606 |
Forum: General Discussions Posted: Mon Jul 25, 2022 4:36 pm Subject: No voltage to air flow meter. |
| My 1988 924s is not getting any voltage to the air flow meter. Does anybody have any suggestions as to why? | |
| Topic: Help with my high beam switch |
|
| 16again2009 Replies: 4 Views: 5470 |
Forum: General Discussions Posted: Tue May 24, 2022 4:10 am Subject: Help with my high beam switch |
| The high/low beam switch is two parts. It has kind of a claw that snaps into the back part. You didn't get that connected when you put it back together. Take it apart again and snap the claw from the ... | |
| Topic: Washers not working, race to pass MOT 😨😨 |
|
| 16again2009 Replies: 7 Views: 10857 |
Forum: 924S Discussions Posted: Fri Apr 29, 2022 7:18 pm Subject: Washers not working, race to pass MOT 😨😨 |
| Happy I could help. Good Luck. | |
| Topic: Washers not working, race to pass MOT 😨😨 |
|
| 16again2009 Replies: 7 Views: 10857 |
Forum: 924S Discussions Posted: Fri Apr 29, 2022 6:20 pm Subject: Washers not working, race to pass MOT 😨😨 |
| If you're sure you got the claw hooked up, the only thing I can think of is a fuse | |
| Topic: Washers not working, race to pass MOT 😨😨 |
|
| 16again2009 Replies: 7 Views: 10857 |
Forum: 924S Discussions Posted: Thu Apr 28, 2022 4:47 pm Subject: Washers not working, race to pass MOT 😨😨 |
| I have a 1988 924s and had this problem a few years ago. I pulled the steering wheel. At the top there is a small copper tab. When you pull the wiper handle back, it moved this tab to make contact wit ... | |
| Topic: 88 Porsche 924s new cat w/ or without 02 sensor port? |
|
| 16again2009 Replies: 1 Views: 11384 |
Forum: 924S Discussions Posted: Tue Feb 01, 2022 5:10 am Subject: 88 Porsche 924s new cat w/ or without 02 sensor port? |
| I just looked under my 1988 924s. The o2 sensor is on the header pipe, not the cat. It only has one 02 sensor. | |
| Topic: No go ?? |
|
| 16again2009 Replies: 6 Views: 15230 |
Forum: 924S Discussions Posted: Mon Oct 11, 2021 4:17 pm Subject: No go ?? |
| I bought a 1988 924s a few years ago. When I got it running it did the same as yours. It was the rubber clutch disc. Its a big job to change. Good Luck. | |
| Topic: 1987 924s 5spd poor/no acceleration when hot |
|
| 16again2009 Replies: 9 Views: 20947 |
Forum: 924S Discussions Posted: Mon Oct 11, 2021 2:14 am Subject: 1987 924s 5spd poor/no acceleration when hot |
| there is a guy on the pelican forum that had sort of the same problem as you, but not exactly. It turned out to be his o2 sensor. You might check that. Just unplug it and see if it runs better.
.pe ... |
|
| Topic: 1987 924s 5spd poor/no acceleration when hot |
|
| 16again2009 Replies: 9 Views: 20947 |
Forum: 924S Discussions Posted: Thu Sep 30, 2021 2:46 am Subject: 1987 924s 5spd poor/no acceleration when hot |
| Did you figure the problem out? | |
| Topic: Brake bleeding |
|
| 16again2009 Replies: 1 Views: 3919 |
Forum: General Discussions Posted: Sun Aug 01, 2021 2:32 pm Subject: Brake bleeding |
| I would bleed at least one of them to make sure your master cylinder is moving fluid. If it doesn't, that's your problem. | |
| Topic: 1987 924s annoying wiper switch issue |
|
| 16again2009 Replies: 2 Views: 7297 |
Forum: Body and Interior Posted: Fri Jul 30, 2021 11:59 am Subject: 1987 924s annoying wiper switch issue |
| I have had some experience with this. If you look in the crack between the steering wheel and the hub, from the top, you will see a small metal tab. You need to bend it a little bit so it makes contac ... | |
| Topic: water pump 924s |
|
| 16again2009 Replies: 5 Views: 19248 |
Forum: 924S Discussions Posted: Sat Feb 13, 2021 2:45 pm Subject: water pump 924s |
| Did you find the problem? | |
| Topic: water pump 924s |
|
| 16again2009 Replies: 5 Views: 19248 |
Forum: 924S Discussions Posted: Fri Feb 05, 2021 7:12 am Subject: water pump 924s |
| Van Svenson has a 3 part video about changing the belts and the water pump. Its on a turbo but the process is the same. It shows everything you will ever need to know in this area. see attached link. ... | |
| Topic: water pump 924s |
|
| 16again2009 Replies: 5 Views: 19248 |
Forum: 924S Discussions Posted: Fri Feb 05, 2021 7:00 am Subject: water pump 924s |
| Can you give a better description of the noise. Is it whining, squealing, banging? | |
All times are GMT + 10 Hours |
Powered by phpBB © 2001, 2005 phpBB Group