Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Intermediate Shift Linkage Disassembly

 
Post new topic   Reply to topic    924Board.org Forum Index -> General Discussions
View previous topic :: View next topic  
Author Message
agfisher  



Joined: 09 May 2007
Posts: 478
Location: West Hartford, CT

PostPosted: Mon May 25, 2020 12:18 pm    Post subject: Intermediate Shift Linkage Disassembly Reply with quote

Anybody know how to take this thing apart to clean and replace the bushings?



I'm trying to remove the red circled part from the blue circled part. I can get the nut (5) off and the washer (11) comes off. Sealing ring ( comes off but then the red unit is immobile. It moves on the pin so it's not frozen. It just doesn't want to move. Has anyone taken one of these apart?
_________________
1977 924 N/A Martini Edition
Back to top
View user's profile Send private message AIM Address
MikeJinCO  



Joined: 08 Jun 2010
Posts: 1227
Location: Maysville, Colorado

PostPosted: Mon May 25, 2020 9:49 pm    Post subject: Reply with quote

I've had that apart but only with tranny off the car. An outfit called 944 Only has a replacement linkage for that for about $50 which I have on the track car which gets rid of the bushings and uses rod ends. He also had directions as to how to get in there to replace it. I think he used a cutoff 17mm wrench to get in there due to the tight space. If you would put a jack under the trans and loosen the hangers it might rotate down a bit to get a little more room. Good luck
_________________
Mike


'67 MG Midget Dp
'71 Ocelot Dsr Kawasaki 1000(under rebuild)
Back to top
View user's profile Send private message Visit poster's website
MikeJinCO  



Joined: 08 Jun 2010
Posts: 1227
Location: Maysville, Colorado

PostPosted: Mon May 25, 2020 10:14 pm    Post subject: Reply with quote

I just looked 944Only up and he is out of them. He used a 11mm wrench about 1" long. Does have some directions on the site which might help. I need to pull the gas tank as I have a bad leak, probably the normal crack and was going to get one.
_________________
Mike


'67 MG Midget Dp
'71 Ocelot Dsr Kawasaki 1000(under rebuild)
Back to top
View user's profile Send private message Visit poster's website
agfisher  



Joined: 09 May 2007
Posts: 478
Location: West Hartford, CT

PostPosted: Mon May 25, 2020 10:52 pm    Post subject: Reply with quote

Transmission is out of the car as part of a fuel tank rebuild. Also, I have a 4 speed which I don't think works with the conversion.

My problem is that the piece just dont seperate. Almost like they have been pressed together but they freely move. It's strange.

Adam
_________________
1977 924 N/A Martini Edition
Back to top
View user's profile Send private message AIM Address
Display posts from previous:   
Post new topic   Reply to topic    924Board.org Forum Index -> General Discussions All times are GMT + 10 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group