Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Question on part

 
Post new topic   Reply to topic    924Board.org Forum Index -> General Discussions
View previous topic :: View next topic  
Author Message
ted von Kampen  



Joined: 14 Oct 2016
Posts: 96
Location: Scottsbluff, Nebraska

PostPosted: Tue Jul 17, 2018 3:55 pm    Post subject: Question on part Reply with quote

I have been working on rebuilding my 1981 Porsche 924. I removed the center console and dash for recovering. There is one part that I cannot remember where it goes. The part in question is a large two fingered clamp attached to a metal bar about 6 inches long with a hole on one end and screw nut on the other. I inquired of a parts supplier what this part is and where it goes. I was told that it was to hold the radio in place. I don't doubt they are right but I cannot quite see how it is placed and how it works. I thought I would ask the forum if a similar part was noted and how it was fastened in the car. If you have one and can take a photo of it I will send you an email address to send the photo.
thanks in advance for your help.
'Ted
Back to top
View user's profile Send private message
gerben1986  



Joined: 13 Mar 2008
Posts: 218
Location: The Netherlands

PostPosted: Mon Jul 23, 2018 2:07 am    Post subject: Reply with quote

Hi, could you post a picture so we get a clear idea?
Does it look like this?: https://www.ebay.de/p/Porsche-477805592/1015690141?_trksid=p2047675.l2644
That's partnumber: 477 805 592
_________________
911SC - 1980
Back to top
View user's profile Send private message Visit poster's website
ted von Kampen  



Joined: 14 Oct 2016
Posts: 96
Location: Scottsbluff, Nebraska

PostPosted: Tue Jul 24, 2018 1:40 am    Post subject: Picture of mystery bracket Reply with quote

See picture in link below

https://www.ebay.com/itm/EXCELLENT-ORIGINAL-GENUINE-PORSCHE-924-944-RADIO-INSTALLATION-BRACKET-CONSOLE/362067960034?fits=Make%3APorsche%7CModel%3A924&epid=2168136634&hash=item544ceea0e2%3Ag%3Ag5kAAOSwyBhZjfoB&_sacat=6000&_nkw=porsche+924+radio+bracket&_from=R40&rt=nc&_trksid=m570.l1313
Back to top
View user's profile Send private message
924RACR  



Joined: 29 Jul 2001
Posts: 8115
Location: Royal Oak, MI, USA

PostPosted: Tue Jul 24, 2018 4:23 am    Post subject: Reply with quote

I was wondering if that was the part you were talking about!

The two prongs face backwards towards the shifter, so that the radio will slide between them.

The flat bar with two holes sits on top of the carpet, on top of the tunnel, bolted to the tunnel with two screws vertically down through those two holes.

The two little flanges on the end, with room for small sheetmetal screws, are to support the center console sides.
_________________
Vaughan Scott
Webmeister
'79 924 #77 ITB racecar
'82 931 Plat. Silver
#25 Hidari Firefly P2 sports prototype
Back to top
View user's profile Send private message Send e-mail Visit poster's website
ted von Kampen  



Joined: 14 Oct 2016
Posts: 96
Location: Scottsbluff, Nebraska

PostPosted: Tue Jul 24, 2018 4:28 am    Post subject: Radio Mount Reply with quote

Thanks, that is what I needed to know. I put down new carpet so probably covered my holes. --Ted
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    924Board.org Forum Index -> General Discussions All times are GMT + 11 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group