Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 1275 matches
924Board.org Forum Index
Author Message
  Topic: Transmission Swap -workout -nightmare
augidog

Replies: 5
Views: 1841

PostForum: General Discussions   Posted: Mon Aug 13, 2007 10:37 am   Subject: Transmission Swap -workout -nightmare
The gears are fine - just real tight to pull in and out- Is this normal for a trans that has been sitting for a long time?- Will it loosen up on its own?
  Topic: Transmission Swap -workout -nightmare
augidog

Replies: 5
Views: 1841

PostForum: General Discussions   Posted: Sun Aug 12, 2007 11:56 am   Subject: Transmission Swap -workout -nightmare
Well -I finally had a good day to swap trans.
Everything went fine until I tried to get the coupling back on.
I was done- except for the coupling menace. The only thing that saved me today was this ...
  Topic: old trans -new oil question
augidog

Replies: 2
Views: 1191

PostForum: General Discussions   Posted: Mon Jul 30, 2007 12:25 pm   Subject: old trans -new oil question
I finally got the trans off the parts car. The coupling was rusted. Someone said in another post to just use a extension ratchet and a hammer-That did the trick once I got a good corner shot to hit
...
  Topic: Maybe stupid question, but has me stumped (cooling)
augidog

Replies: 7
Views: 2350

PostForum: General Discussions   Posted: Mon Jul 30, 2007 5:04 am   Subject: Maybe stupid question, but has me stumped (cooling)
Try a new radiator cap. It may not be holding pressure.
  Topic: Thanks to Chrenan...
augidog

Replies: 13
Views: 4122

PostForum: General Discussions   Posted: Tue Jul 17, 2007 11:42 am   Subject: Thanks to Chrenan...
http://members.localnet.com/~djmeijer/27561442out.JPG
  Topic: Rare Pic of Three 924 Geeks from Three Countries. . .
augidog

Replies: 14
Views: 5873

PostForum: General Discussions   Posted: Thu Jul 12, 2007 11:08 am   Subject: Rare Pic of Three 924 Geeks from Three Countries. . .
They forgot to mention that I was there too.

It was a blast!!!!!
The first day was a little cold and rainy.



Kenodog was a little shy at first -but we became best buddys after he borrowed my ...
  Topic: oil filter relocation
augidog

Replies: 13
Views: 4414

PostForum: General Discussions   Posted: Fri Jul 06, 2007 11:35 am   Subject: oil filter relocation
I talked to this seller a while ago. He can piece anything together you may need. His complete kits look good for the money.I ran into other repairs so I did not personally order mine- yet.

http:/ ...
  Topic: Not starting after replacing head
augidog

Replies: 6
Views: 2153

PostForum: General Discussions   Posted: Wed May 30, 2007 10:47 am   Subject: Not starting after replacing head
hey flame,

watch out! There are Dot-Marks on both sides of the cam-wheel!!
They have a quarter offset,so make sure its installed the same way then before.

Nobby

This happened to m ...
  Topic: Vacuum line on intake boot.
augidog

Replies: 20
Views: 5846

PostForum: General Discussions   Posted: Tue May 29, 2007 10:02 am   Subject: Vacuum line on intake boot.
Smoothie is right - it is the decel valve. If you bypass it you will raise your vac up about 3-5 points hence the quicker idle. But you will backfire and the car will sound like crap. I plan to remov ...
  Topic: Early Ignition Distributor vs Late?
augidog

Replies: 30
Views: 8517

PostForum: General Discussions   Posted: Tue May 29, 2007 9:37 am   Subject: Early Ignition Distributor vs Late?
If you put the distributor in and plug both vacuum holes it will run on strickly mechanical advance. If you set your timing to 0, if will give you a max advance of 36 degrees. It is a 30 degree distri ...
  Topic: Tyres / Tires
augidog

Replies: 3
Views: 1740

PostForum: General Discussions   Posted: Fri May 11, 2007 10:40 am   Subject: Tyres / Tires
I like the original size tire on the car. I ran both. The 185's seem a little more lively on the road.
  Topic: Cam Oiler Elbow..
augidog

Replies: 24
Views: 5623

PostForum: General Discussions   Posted: Fri May 11, 2007 10:31 am   Subject: Cam Oiler Elbow..
Its been a couple years but I got that part at a VW dealership for under $5.00
If you pass one, stop in with the number and ask.
  Topic: cracked exhaust manifold
augidog

Replies: 20
Views: 6830

PostForum: General Discussions   Posted: Fri May 04, 2007 11:29 am   Subject: cracked exhaust manifold
It split right in half at the thickest point 2 miles from home.
  Topic: Head Rebuild
augidog

Replies: 16
Views: 4787

PostForum: General Discussions   Posted: Sun Apr 29, 2007 10:38 am   Subject: Head Rebuild
If you pulling the head and have not done the bottom. Do both. This was a mistake I made. You can always bolt on a new cam and header later.
  Topic: Timing, timing
augidog

Replies: 7
Views: 1895

PostForum: General Discussions   Posted: Sun Apr 22, 2007 10:57 am   Subject: Timing, timing
Are you adjusting the mix as well?
 
Page 1 of 85 Goto page 1, 2, 3 ... 83, 84, 85  Next
All times are GMT + 11 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group