Author |
Message |
Topic: Project Turbo Manifold - final design assembly |
MunkPuppy
Replies: 222
Views: 103925
|
Forum: Performance Upgrades Posted: Sun Jun 17, 2007 5:59 am Subject: Project Turbo Manifold - final design assembly |
does anyone have copies of the drawings that OOTB posted? They're all FILE NOT FOUND now, and CBass & I wanted to look them over and maybe make up a couple. |
Topic: 2-spoke vs. 3-spoke steering wheel... |
MunkPuppy
Replies: 25
Views: 12744
|
Forum: General Discussions Posted: Thu Mar 22, 2007 1:49 pm Subject: 2-spoke vs. 3-spoke steering wheel... |
has anyone informed Momo that their car is a 944, not a 969? |
Topic: WOW! |
MunkPuppy
Replies: 31
Views: 21272
|
Forum: 931 Discussion Posted: Tue Feb 20, 2007 9:12 pm Subject: WOW! |
I built my replacement bushings from aluminum, and yes it does rattle a little, but I just didn't have any urethane available at the time. the build would have been the same using either material; I t ... |
Topic: Turbo questions. EDIT: BAE Turbo questions |
MunkPuppy
Replies: 5
Views: 2504
|
Forum: General Discussions Posted: Sun Sep 17, 2006 1:06 pm Subject: Turbo questions. EDIT: BAE Turbo questions |
if it happens that your turbo needs to be rebuilt, don't make the mistake I did and try doing the rebuild yourself. There are quite a number of tolerances that, if not within spec, will make your rebu ... |
Topic: Fuel system problems |
MunkPuppy
Replies: 4
Views: 2281
|
Forum: 931 Tech. Posted: Thu Jul 06, 2006 4:18 pm Subject: Fuel system problems |
I had this issue with my car, and it turned out that the ignition coil was getting power during cranking, but none after the starter was disengaged. A jumper between 2 wires in the engine harness and ... |
Topic: ECOTEK CB-26P Valve |
MunkPuppy
Replies: 19
Views: 11731
|
Forum: Performance Upgrades Posted: Thu Jul 06, 2006 3:29 pm Subject: ECOTEK CB-26P Valve |
of course you can! it's standard wire loom, which by default comes in black. Go to any auto parts store, they should have it. |
Topic: OT: Blend -> Synthetic Motor Oil |
MunkPuppy
Replies: 12
Views: 4631
|
Forum: General Discussions Posted: Fri Jun 23, 2006 3:01 pm Subject: OT: Blend -> Synthetic Motor Oil |
I'm 100% for going to syn oil! If possible, do an engine flush before you drain the old oil out, it will help flush out some of the sludge to make your first syn oil change a little less "contami ... |
Topic: Turbo Gaskets |
MunkPuppy
Replies: 8
Views: 3597
|
Forum: 931 Tech. Posted: Mon Jun 12, 2006 2:56 pm Subject: Turbo Gaskets |
I got the O-Ring size from the online PET (47mm X 5.7mm), brought my old O-Ring as well, and went to my local auto parts shop and compared sizes to what they had in stock. I bought a few O-rings, thic ... |
Topic: WOW! |
MunkPuppy
Replies: 31
Views: 21272
|
Forum: 931 Discussion Posted: Mon Jun 12, 2006 2:42 pm Subject: WOW! |
Did you change your trans to a used dog-leg one or did you convert to Audi-style?
The car came stock w/ a G31, and I bought another used G31 from Lizard, which is still waiting to be installed. A b ... |
Topic: WOW! |
MunkPuppy
Replies: 31
Views: 21272
|
Forum: 931 Discussion Posted: Sat Jun 03, 2006 7:38 am Subject: WOW! |
I have FINALLY taken to task and completed the needed repairs to get my 931 mobile again. I have to say, I have dearly missed driving my 931, and now I remember why.
Repairs completed:
Transmissio ... |
Topic: Knock sensor? |
MunkPuppy
Replies: 8
Views: 3712
|
Forum: General Discussions Posted: Sat Mar 11, 2006 12:06 pm Subject: Knock sensor? |
actually, Uncle Buck's car was dieseling... knocking makes a loud rattling noise under load or acceleration. |
Topic: shifter |
MunkPuppy
Replies: 6
Views: 4248
|
Forum: General Discussions Posted: Sat Mar 11, 2006 11:51 am Subject: shifter |
This is what Lizard is talking about... I have it installed, but the car isn't drivable yet since I haven't put the exhaust back in nor have I replaced my bent tie rod or reinstalled my freshly repack ... |
Topic: 931 headlight assembly |
MunkPuppy
Replies: 2
Views: 1619
|
Forum: 931 Tech. Posted: Fri Feb 17, 2006 2:44 pm Subject: 931 headlight assembly |
to my knowledge (feel free to correct me, peeps), the headlight motor on the 931 is on the opposite side as the 924. This is to accomodate the location of the CIS fuel distributor in the 931. |
Topic: 2010 Porsche 928? |
MunkPuppy
Replies: 37
Views: 15536
|
Forum: General Discussions Posted: Thu Feb 16, 2006 2:03 pm Subject: 2010 Porsche 928? |
I don't think it's fair to criticize Porsche Motorenwerk for expanding their product line. Sure, they've come out with the Cayman (which is a hard-top Boxster), and the Cayenne.. but through all of th ... |
Topic: OT: If GM had designed the 911..... |
MunkPuppy
Replies: 17
Views: 6146
|
Forum: General Discussions Posted: Thu Feb 16, 2006 1:33 pm Subject: OT: If GM had designed the 911..... |
hey all of you canucks, you should already know what this is... it's a porsche done in the CHEVRON TECHRON COMMERCIAL theme!! |
|