Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 76 matches
924Board.org Forum Index
Author Message
  Topic: WUR banjo fitting-need help
Mudd

Replies: 12
Views: 3833

PostForum: General Discussions   Posted: Sun Jul 21, 2013 1:14 am   Subject: WUR banjo fitting-need help
I twisted the head off of the smaller banjo bolt on the WUR. Can someone tell me the part number for the WUR banjo bolts. Are these usually available at my local car parts place or do I need to buy ...
  Topic: WUR banjo fitting-need help
Mudd

Replies: 12
Views: 3833

PostForum: General Discussions   Posted: Sun Jul 14, 2013 12:05 pm   Subject: WUR banjo fitting-need help
Great information Ideola, thanks. I just ordered the correct washers from Pelican. Thanks for everybody's replies
  Topic: WUR banjo fitting-need help
Mudd

Replies: 12
Views: 3833

PostForum: General Discussions   Posted: Sun Jul 14, 2013 7:00 am   Subject: WUR banjo fitting-need help
Sorry to be such a dumb ass but what does anneal mean..
  Topic: WUR banjo fitting-need help
Mudd

Replies: 12
Views: 3833

PostForum: General Discussions   Posted: Sun Jul 14, 2013 6:30 am   Subject: WUR banjo fitting-need help
I went to the car parts place and they sold me copper washers that he said are the same thing as fuel crush washers. Put one on each side of the banjo bolt, tighten down good, started the car and I ha ...
  Topic: WUR banjo fitting-need help
Mudd

Replies: 12
Views: 3833

PostForum: General Discussions   Posted: Sun Jul 14, 2013 5:03 am   Subject: WUR banjo fitting-need help
One more question, is it necessary to put a washer on both sides of the banjo fitting, two on each bolt.
  Topic: WUR banjo fitting-need help
Mudd

Replies: 12
Views: 3833

PostForum: General Discussions   Posted: Sun Jul 14, 2013 4:09 am   Subject: WUR banjo fitting-need help
I removed my wur and cleaned it. I notice when I was putting it back on that the upper or larger banjo bolt did not have a washer on it. Don,t know if if had one on it when I took it off or if I los ...
  Topic: A/F
Mudd

Replies: 8
Views: 1701

PostForum: General Discussions   Posted: Sat Jul 13, 2013 12:54 am   Subject: A/F
I am going to clean my WUR and I have been screwwing with the air bypass screw, so after the WUR is clean I figure I will have to adjust something to get my idle correct. I replaced all of the vacuum ...
  Topic: A/F
Mudd

Replies: 8
Views: 1701

PostForum: General Discussions   Posted: Fri Jul 12, 2013 1:07 am   Subject: A/F
Where is the A/F mixture adjusting screw on a 1978 924.
  Topic: Cleaning my WUR
Mudd

Replies: 9
Views: 2789

PostForum: General Discussions   Posted: Tue Jul 09, 2013 12:32 am   Subject: Cleaning my WUR
John, the point of my post is that I think removing the WUR is going to be a major pain in the ass and was asking how much stuff should I expect to remove to get to it. Did you get yours out, and if ...
  Topic: Cleaning my WUR
Mudd

Replies: 9
Views: 2789

PostForum: General Discussions   Posted: Wed Jul 03, 2013 11:21 pm   Subject: Cleaning my WUR
I am going to remove and clean my WUR this weekend on my 78 924. My question is how much stuff do I have to remove to get to the WUR. What should I expect when I remove the fuel lines. Will they be ...
  Topic: Gas cap pressure
Mudd

Replies: 2
Views: 871

PostForum: General Discussions   Posted: Sat Jun 29, 2013 12:53 pm   Subject: Gas cap pressure
Can someone please direct me to an article about servicing the charcoal canister. Could this gas pressure have something to do with my high idle problem.
  Topic: Gas cap pressure
Mudd

Replies: 2
Views: 871

PostForum: General Discussions   Posted: Sat Jun 29, 2013 8:29 am   Subject: Gas cap pressure
When I unscrew my gas cap I have to let the pressure bleed off before I fully open the cap. The pressure bleeds off for a good 20 seconds. Is this normal or do I need a new gas cap.
  Topic: So what does this mean to you,....
Mudd

Replies: 8
Views: 2609

PostForum: General Discussions   Posted: Wed Jun 12, 2013 3:22 am   Subject: So what does this mean to you,....
Great find. How about some pictures of the whole car.
  Topic: CIS Test kit
Mudd

Replies: 10
Views: 3730

PostForum: General Discussions   Posted: Thu May 30, 2013 11:36 am   Subject: CIS Test kit
I found a CTA 3420 Bosch K jetronic CIS fuel injector pressure tester for $110 on Amazon. Is that what I need.
  Topic: CIS Test kit
Mudd

Replies: 10
Views: 3730

PostForum: General Discussions   Posted: Thu May 30, 2013 11:36 am   Subject: CIS Test kit
I found a CTA 3420 Bosch K jetronic CIS fuel injector pressure tester for $110 on Amazon. Is that what I need.
 
Page 1 of 6 Goto page 1, 2, 3, 4, 5, 6  Next
All times are GMT + 10 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group